2014 Latest Cisco 350-001 Dump Free Download(261-270)!

QUESTION 261
Which two are IPv6 neighbor discovery packets? (Choose two.)

A.    Neighbor Solicitation
B.    Anycast Solicitation
C.    Anycast Advertisement
D.    Router Advertisement

Answer: AD
Explanation:
http://packetlife.net/blog/2008/aug/28/ipv6-neighbor-discovery/

QUESTION 262
Which individual metrics can be used to calculate the composite EIGRP metric?

A.    total delay, minimum bandwidth, reliability, load, MTU
B.    total delay, minimum bandwidth, reliability, load, MTU, hop count
C.    total delay, minimum bandwidth, reliability, load, hop count
D.    total delay, minimum bandwidth, reliability, load
E.    total delay, minimum bandwidth

Answer: D
Explanation:
http://www.cisco.com/en/US/docs/ios-xml/ios/iproute_eigrp/configuration/15-sy/ire-wid- met.html#GUID-736131DE-0B64-46F4-A19A-B0526D24F95B (See table 1)

QUESTION 263
In which two scenarios would MSDP be used? (Choose two.)

A.    Interdomain multicast
B.    Anycast RP
C.    Distributing the RP address to other routers
D.    Implementing PIM-SSM

Answer: AB
Explanation:
http://tools.ietf.org/html/rfc4611 (see introduction)

QUESTION 264
Which four are possible states in the BGP FSM? (Choose four.)

A.    Idle
B.    Established
C.    Wait
D.    Active
E.    OpenSent
F.    Nonconnected

Answer: ABDE
Explanation:
http://www.freesoft.org/CIE/RFC/1771/52.htm (See the table)

QUESTION 265
Which command should be used on a PE router to connect to a CE router (11.1.1.4) in VRF red?

A.    telnet 11.1.1.4 /vrf-source red
B.    telnet 11.1.1.4 source /vrf red
C.    telnet 11.1.1.4 /source vrf red
D.    telnet 11.1.1.4 /vrf red
E.    telnet 11.1.1.4 vrf red

Answer: D
Explanation:
You would need to telnet the ce router in vrf red. The correct syntax is telent ipaddress/vrf red.

QUESTION 266
Which address needs to be present on an interface for OSPFv3 to form an adjacency?

A.    Global unicast
B.    Unique local
C.    Link local
D.    FF02::5
E.    FF02::6

Answer: C
Explanation:
OSPFv3, however, makes use of IPv6’s link-local address scope (FE80::/10). All OSPFv3 adjacencies are formed using link-local addresses:
R1# show ipv6 ospf neighbor detail
Neighbor 3.3.3.3
In the area 1 via interface FastEthernet0/0
Neighbor: interface-id 4, link-local address FE80::C003:7DFF:FE07:0 Neighbor priority is 1, State is FULL, 6 state changes
DR is 3.3.3.3 BDR is 2.2.2.2
Options is 0x6670B96D
Dead timer due in 00:00:32
Neighbor is up for 00:16:48
Index 1/1/1, retransmission queue length 0, number of retransmission 0 First 0x0(0)/0x0(0)/0x0(0) Next 0x0(0)/0x0(0)/0x0(0)
Last retransmission scan length is 0, maximum is 0
Last retransmission scan time is 0 msec, maximum is 0 msec

QUESTION 267
By default, EIGRP will use which percentage of bandwidth on an interface?

A.    10%
B.    25%
C.    50%
D.    75%
E.    80%
F.    100%

Answer: C
Explanation:
The enhanced implementation uses the configured interface bandwidth in order to determine how much EIGRP data to transmit in a given amount of time. By default, EIGRP will limit itself to using no more than 50% of the interface bandwidth. The primary benefit of controlling EIGRP’s bandwidth usage is to avoid losing EIGRP packets, which could occur when EIGRP generates data faster than the interface line can absorb it. This is of particular benefit on Frame Relay networks, where the access interface bandwidth and the PVC capacity may be very different. A secondary benefit is to allow the network administrator to ensure that some bandwidth remains for passing user data, even when EIGRP is very busy.

QUESTION 268
From which IPv6 address are EIGRPv6 hello messages sourced?

A.    Global unicast
B.    Link local
C.    Site local
D.    Unique local
E.    FF02::A

Answer: B
Explanation:
Link local address is the address being used in EIGRPv6 as the next hop address in the IPv6 routing table, it is required that the engineer map both the link-local & global addresses to an interface in the EIGRPv6 configuration as well. EIGRPv6-enabled routers will not become adjacent without the link-local mapping, even if the global address mapping exist on the router.

QUESTION 269
What is the Internet Protocol Number for all PIM control Messages?

A.    15
B.    17
C.    25
D.    103

Answer: D
Explanation:
http://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml (search `103′)

QUESTION 270
Which value is used in the PIM TYPE field to indicate a Join/Prune message?

A.    0
B.    1
C.    2
D.    3

Answer: D
Explanation:
http://tools.ietf.org/html/draft-venaas-pim-hierarchicaljoinattr-00

 

If you want to pass the Cisco 350-001 Exam sucessfully, recommend to read latest Cisco 350-001 Dump full version.